Wednesday, November 20, 2013

Gluing

I had thought I would enjoy gluing since it seemed a delightfully swift easy and imprecise business. It isn't and I don't. It's surprisingly hard to find out how anybody else does gluing, so my method - thus far - is this, which will be a useful addition to the sum of human knowledge only until such time as my boat falls apart and I drown to death.

1. Gloves. You need an awful lot of rubber gloves. Disposable ones, latex. Not the thin plastic disposable ones: they don't mould to your fingers. And not kitchen gloves: they don't turn inside out easily. The game is to don gloves, commence operations, and the moment stickiness is detected on the fingers, peel the glove off by turning it inside out, and drop it on the floor. The glue is thereby contained inside the glove and will harden, and tomorrow you can turn the glove back outside-in by spinning it round on its own wrist, using the trapped air to squeeze all the fingers out. This I discovered courtesy of the Arthur Rickwood Experimental Station where rubber gloves were worn extensively, and where I learnt that blowing into the gloves to pop the fingers out results in a moist interior, which means you can't then get your hand in. - The most significant contribution that august body made to the cause of science. We are apt to over-rate our place of importance in the world, especially if a government research station. - If I remember correctly, there was a senior scientific officer there called Brian Tucker and daily another of the senior scientific officers took a felt pen and altered the spelling of the label on his office door. I remember this fact whenever I hear of a schoolteacher admonishing a teenager to act his age. - A certain teenager whose name I shall not mention is about to leave school, and has received a good deal of schoolteacher admonishment of late. His final prank a few days ago was to tell the local newspaper that he was a rugby player and that (quoting)  he singled out the Principal for his "inspiring speeches in assembly" which, against all the evidence, they believed and printed. - During the interview the reporter asked him what position in rugby he played, for which question he was wholly unprepared, and knowing only one position in a rugby team he declared 'hooker'. Afterwards we looked up hooker and found it to be the biggest, muscliest man in the team, not a spindly bespectacled boy with a head for calculus. Evidently the reporter isn't a rugby enthusiast either, since he printed the story intact. - Where were we? - Recycling gloves, that's where. - Gloves last three or four uses, I find.



2. Syringes. The epoxy requires accurate measuring of resin and hardener. I use a 20 millilitre syringe for the resin and a 5 ml syringe for the hardener. Each has a length of 5mm PVC tubing jammed onto the spout to reach the liquid towards the bottom of the canister. The used syringe is immediately put inside a sealed screw-top plastic jar, so it stays wet and uncontaminated, and later I use it again. As everything's hardening you find bubbles of air under some of the glass-fibre tape, and a 1ml syringe, having a small bore, allows high enough pressure to inject epoxy through a 1.6 mm hypodermic needle. Obtained by mugging a drug addict. - Actually this region doesn't do hypodermic needles, only cannabis, which one stumbles upon deep in the bush, a small clump of carefully weeded plants growing behind a fence of chicken wire to keep the feral goats out. I've happened on it several times in the National Parks. The police used to harvest the plants and do a large bonfire in the car park until the locals became too enthusiastic about yesterday's bread. - The police station is next door to what was the baker, and the car park was adjacent to the air intakes of their ovens.

3. Mixing. The resin is injected into a round plastic ice cream carton and the syringe put away. Then the hardener is injected on top of the resin and that syringe put away. Then a lolly stick is used carefully to mix the two together. Mostly I use 39 ml resin and 13 ml hardener and that's enough to keep me busy. Takes a couple of minutes to mix it. Mixing became easier when I abandoned the Thai takeaway dishes which had a ridged centre section. There's an army of plastic extrusion engineers out there making shapes more complicated than they need be and they ought all to be sacked. The mixed resin-and-hardener is a slightly viscous liquid. I use it raw (without fillers) to wet the fibreglass tape.

4. Tape. As instructed by everyone, I cut the cloth into tape on the bias (that is, all strands at 45 degrees to the length) so every fibre crosses the joint. At first I cut a single length of tape, but when wet with epoxy all the fibres turn into parallelograms and the tape became a rope 1.414 times as long and I needed a third hand to apply it, which I didn't possess. So now my method is to:
a) cut twenty pieces of fibreglass cloth, half of the pieces an inch wide, half two inches wide, all of them three inches long.
b) mix 39ml resin with 13ml hardener.
c) put the first bit of cloth in a Thai tray and paint it with epoxy till it's wet through. I use a stabbing motion of the brush, not a brushing motion which draws the fibres out and makes a mess. (Stabbing motion with a brush is called stippling, if you're the sort of person who knows what stippling means.)
d) put the next bit of cloth on top of that one, and again stipple it till wet with epoxy.
e) carry on till all the bits of fibreglass cloth are soaked through and piled on top of each other.

5. Glue. To make the epoxy into glue you have to use HT120 filler. Otherwise it's just a liquid without any body to it, and it runs out of the joints and leaves them starved of glue. I add a teaspoonful of HT120 and stir it in to make a very liquid glue and use the paintbrush to wet out the wood thoroughly and penetrate all the gaps between the seams making sure every bit of wood is wetted, and there's a healthy inch or so wet on either side of the actual joint. Work the wet under the fishing line. Then I squeegee it all as dry as is possible with my stippling brush, and this leaves about the right amount of glue.

5. Filling. To make filler you use HT450 filler. Both these fillers are fine white powders. I add filler to the remaining epoxy glue, half a teaspoon at a time, until the viscosity feels right. It needs to be stiff enough not to run out of the joint, with the appearance and consistency of a white putty.

Some of my fillers, the bits where I rounded off the inside gaps in between planks, have been a weird mixture of epoxy and HT120, HT450, and teaspoons-full of sawdust. This gives lots of body and appears to be pretty robust material when hardened. The pointy-bits of boat end are filled with this stuff.



I use Mini Magnum lolly sticks as trowels to trowel the filler into the joint. The children provide me with adequate supplies for which I am most grateful. The sticks are washed and dried, and the edge sharpened on a bench grinder. Lots of filler is poked into all gaps and under each of the nylon fishing-line bindings. Any wedges holding the planks in proper alignment have to be removed, glued, and reinserted wet, and this is a ghastly fiddly job because wet wedges go straight through and pop out of the other side of the binding, and you can't get hold of them because you've got wet gloves on, and you can't use a hammer to delicately tap them into place or the hammer handle gets wet and then you'll pick it up afterwards and get glue all over yourself.

When enough is trowelled along the joint, I use either the lolly stick or a piece of closed-cell polyurethane foam as a shaper. This is 6mm thick, 40mm wide, and cut to a semicircle. A single smear of the shaper works well. A second smear roughs everything up and you have to start again, dammit. Both of them seem to work equally well.

6. Tape. Next I lay wet, glued-out tape onto the filled joint. The first layer of tape is laid and pressed down gently into the middle of the filled joint with the fingertips, and then pressed outwards towards either piece of wood. Each short length of tape overlaps the previous one. When the first, inch-wide tapes are down a second layer of two-inch wide tapes are overlaid and pressed down. Wherever bubbles appear, I gently press the tape down with the tip of a lolly stick. And then, because I am rubbish at gluing, I notice a series of worrying white bits of fibreglass and these white bits suggest Glue Starvation inside the glass, so I frantically mix another 9 ml of resin and 3 ml hardener and a small amount of HT120 to make a runny glue, and stipple it into the joint.

7. Lastly, I remove gloves and with great care press strips of two-inch wide masking tape onto the edges of the seam. The masking tape holds the fibres firmly on the wood and allows me to press them home with my fingers. Several hours later it can be peeled off without removing any fibres and I'm left with a clean smooth feather into the woodwork.

8. This process takes about two minutes per inch of joint, and 39ml+13ml will do about 40 inches. Afterwards I wash the brush in acetone, which does actually clean it of epoxy, so I can use it tomorrow. I tip a little acetone into the mixing pot, wash the brush, dry the brush on a sock and put it to dry - the brush, not the sock - and use the sock to dry the mixing pot. And I don't touch any of the gloves on the floor till tomorrow.

9. Fascinating, wasn't it?

10. If you have a broken bicycle spoke on your desk you can twang it like a ruler and annoy everyone. This discovery is not material to gluing a joint of a plywood proa, but as I happen to have a such a spoke to hand, I thought I would kindly slip it in.


Labels: , , , ,

Tuesday, October 1, 2013

Sewing

Holes drilled: now to the sewing.  Easy, methought*.  Wrong. 

First I was going to use monofilament nylon, and then I remembered that I cannot tie it in a million years.  Copper wire, then.  And because I am a miserly hoarder who can't bear to throw rubbish away I delved under the bench for a cardboard box and found therein all the bits of wire that the electrician had left when we did the kitchen. There is a very fortunate thing about electricians, though all the tradesmen complain about it: they never sweep their mess up. When an electrician has visited, you will always find eighty-one short pieces of red, brown and green/yellow plastic coated pieces of copper wire. And what I have now discovered is that provided they're minimum of 63mm in length, they will sew a wooden board to another wooden board.


First there was the obligatory Human Sacrifice. In the olden days when the natives were more tractable you'd get an Aztec and in a hideous illustration found only in National Geographic you'd do away with him in a welter of blood and screams.  Today it is necessary only to let me loose in the workshop. I started to strip the short bits of wire, and one such, the end folded round on itself to facilitate clamping in some unknown appliance, ploughed heartily and without mercy straight through the pulpy end of my left index finger.
"Aaaaah!" I cried.
And then I thought for a half-pico-second, "I am about to regret that."
And then I uttered the usual word.
And then I mopped things up and wandered inside for a plaster.



When you come to sew two flimsy boards together you face the dilemma of how to hold them. This hadn't crossed my stupid mind beforehand: I  simply thought "Sew!" but actually wood isn't as pliable as any of the other things you might be called on to sew and you can't get your hand and eyeball underneath a board that's lying on the floor.  Eventually I realised that since the two garboard strakes would be as a Vee with one another, they would stand upright on the floor at the back. I propped them both up vertically for the first stitch, and so it proved.

After five stitches I thought "I wonder if the middle bit of the bottom ought to be flatter."  And I started to wonder how flat the bottom ought to be if the finished thing was to turn in the water when I want it to tack.  And then I thought "Actually, I don't know what I'm doing here", so I popped next door and dragged Graeme over, and he told me that Wharram sews the sides together flat, and then forces them apart and they make their own rocker. "Get on with it" he said, not for the first time, "and then you'll see what will work."

When he'd gone I thought  "I wonder how long it will be until I gouge myself on one of these exposed sharp copper wire ends."  So I crept up into the loft and got a roll of 35lbs breaking strain nylon monofilament and found that it is, actually,  possible to tie a timber hitch and jam it in one of the holes - they're 2mm in diameter - and then to sew three times through it creating two loops, which is a holding-together-strength of 70 lbs.



However. When you come to open the two boards apart, you find they don't want to pivot on one another's corner. One instantly slips down onto t'other. So this was going to be a problem. And then I thought that since the nylon sewing was going rather well I'd remove the copper stitches before they stabbed me again, a rare moment's prudency. Running short of fishing line I had to nip to the Warehouse, the Warehouse, where everything's open and broken, because all the other shops were shut. (Otherwise I never go there, on principle.)  I discovered that they didn't have any 35lbs fishing line, and true to form when I got their 40lbs home I found it was thinner and weaker than the 35lbs I'd got from Walkers of Trowell 27 years ago. Trowell is where sometimes NFI was to be found written in a patient's notes, standing for Normal For Ilkeston. (They had several of these acronyms. FLK meant Funny Looking Kid, so some startled young paediatrician didn't go off doing hundreds of unnecessary invasive tests.)

Nevertheless the 40lbs monofilament held, and even allowed me to open the whole thing apart, when I discovered that I was, after all, going to need some formers to hold the two planks at the correct angle to one another, or the end wouldn't bend upwards at the curve to match my carefully prepared side planks. So I made three formers to see what happened, with angles 22, 44 and 55 degrees off a straight line. (Okay, Mr. Knight you horrid mathematician, with angles of 158, 136 and 125 degrees.)


Happily, by experimenting, I found that I could vary the amount of rocker by moving the 44 degree former backward or forward, and I don't seem to need the 55 degree former at all.

I was surprised at how much force was needed to prise the planks apart, and got John to help with his bulk and muscle. He was not in a bulk and muscle mood, however: he was in a composing poetry mood. John has a healthy teenage disdain for poetry, and his verse tends toward the irreverent, invariably being brief and also invariably involving words like Knob which have easily thought-of on-the-spot homophones.
"Just lean hard on this, Sir Andrew."
"Who?"
"Andrew Motion. I mistook you for the poet laureate."
"That's a job?"
He was surprised to learn that the job of the poet laureate is, actually, to composed odes and whatnot for state occasions. He immediately had a thought.
"Could I write and ask him to find words that rhyme?"
"You probably could, though I don't know that he'd reply."
"I'll say I'm composing a poem for the Queen's jubilee, and ask him what rhymes with Regina."

Afterwards it occurred to me that I have a car scissor-jack doing nothing, so I screwed it to the rafters to save more poetic ramblings when forcing the planks apart with the permanent formers.


Anyway, all the people who've ever made these things before were right, of course. The nylon will hold everything together, even the very sharply bent tip, provided you sew it very tightly when the boards are flat together like a close book.


And the boards pivoting on their sharp edges didn't turn out to be a problem - all I did was lightly tap them into place with a dowel and a hammer, and the tension of the nylon keeps them there.


Now the epoxy is hardening, with the addition of a 60 watt light bulb as a heater and lots of rags and bits of cardboard to keep the heat in and quite a few checks to be sure it isn't kept in enough to catch fire.


*Methought.  Hapax legomenon - until now - courtesy of Miss Davena Watkin.

Labels: , , , , , , ,